top of page

BRAND NEW CERAMIC TILES SHOWROOM NOW OPENED - 10% OFF FOR ALL WALK IN CLIENTS

Alba Flooring Logo.png

Subfloor Preparation and Levelling: Why It Decides How Your Floor Looks and Lasts

Oct 14
3 min read

When people choose new flooring, they spend hours on colour, pattern and finish, and almost no time on what is underneath. Yet the subfloor often decides whether the finished job looks crisp and lasts for years, or squeaks, lifts, cracks and shows every bump.

If you remember one thing from this guide, make it this: preparation is not an optional extra. It is part of the floor.

What is a subfloor?

The subfloor is the structural surface your new floor sits on. In most homes it will be one of the following:

  • Concrete or sand and cement screed, common in ground floors and many flats.

  • Timber floorboards or sheet material over joists, typical in older houses and upper floors.

  • An existing floor covering, such as old tiles or vinyl, which may or may not be suitable to build on.

Each type has its own strengths and its own problems. A floor fitter will usually start by inspecting the surface for flatness, soundness, moisture and cleanliness.

What can go wrong

Problems with the base rarely stay hidden. They tend to show up in the finished floor in familiar ways:

  1. Hollow or bouncy spots in laminate and engineered boards, caused by dips underneath.

  2. Visible ripples or ridges through vinyl, which tends to mirror whatever is below it.

  3. Cracked or loose tiles, where movement or an uneven bed leaves tiles unsupported.

  4. Squeaks and creaks, often from loose boards or fixings in timber floors.

  5. Staining, cupping or mould, where moisture has reached the new floor.

Many of these are expensive to fix after the event, because the floor has to come up before the cause can be tackled.

Levelling: how flat is flat enough?

Different floors tolerate different amounts of unevenness. As a rule, thin, flexible coverings such as LVT need a very smooth and level base, while thicker boards can forgive slightly more. Large-format tiles also demand a flat surface to avoid lippage, where one tile edge sits higher than its neighbour.

Manufacturers publish tolerances for their products, and fitters measure the floor against them, often using a long straight edge. Where the surface falls outside tolerance, levelling is needed. Common approaches include:

  • Self-levelling compound poured over a primed surface to create a smooth, flat finish.

  • Smoothing and patching compounds for local repairs and feathering edges.

  • Plywood or boards screwed over timber floors to create a stable, even surface.

  • Planing or grinding to remove high spots.

Which method suits you depends on the depth of the problem and the type of floor going down.

Moisture matters

Moisture is a quiet troublemaker. Concrete and screed can hold water for a long time, particularly in newer builds or after a leak. Timber floors can be affected by damp from below. Fitting wood or vinyl over a base that is too damp can lead to swelling, lifting or adhesive failure.

Fitters often test moisture levels before starting, and in some cases a damp-proof membrane is recommended. Follow the guidance for your product, because it can affect the guarantee.

Cleanliness, soundness and old coverings

A base must also be clean and firmly bonded. Dust, paint, grease, old adhesive and loose areas stop new adhesives and compounds from bonding properly. Removing old floors can be messy, but it is often the most reliable route. Old adhesives are another matter, and some older materials need careful handling. If you suspect a floor contains hazardous material, get advice before disturbing it.

How preparation affects cost and timing

Preparation adds time and cost, and the amount varies enormously from room to room. A well-kept flat concrete base may need little, while an old timber floor could need considerable work. This is why a site visit is so valuable. A quote that ignores the subfloor can look cheaper at first and cost more later. When you compare quotes, check what preparation is included.

Frequently asked questions

Can I lay new flooring over my old floor?

Sometimes, if the existing surface is flat, sound and suitable for the new product. It should be assessed first.

Do I need levelling for engineered wood?

Often a degree of levelling is needed, depending on the fitting method and the floor. Your fitter will measure and advise.

Is preparation really worth paying for?

In our experience it is one of the most worthwhile parts of any job, because it protects everything you spend on top of it.

Start with a proper look at your floor

If you are planning new flooring, ask for a survey before you choose the finish. Our team supplies and fits wood flooring, LVT and tiles, and you can see examples of previous work in our portfolio. To arrange a visit or a quote, get in touch.

 
 
 

Recent Posts

See All

Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
bottom of page
Website by Merx Marketing